I want to run three ledenet 16' strip lights in series (48' total). do i need this to boost the power to the strips?

This is ment to boost the total output to 24A. You can connect as many strips as you want as long as the total current of the strips is less than 24A. You can get from the strips specs the current in A/m and add the total length of your strips to see how much they will actually consume. Make sure your power supply is capable to deliver the same value multiplied by three. I will not go with three strips in serial because the last string will look dimmer. You can connect them in parallel and make sure in any case the cables you use have enough gage for the current passing through them.

I want three 20' runs, do i just need this, the leds, and controller? can i run them in parallel off the output channel? is there a wiring diagram?

I used this amp to power and control three runs of lights using the output of one RGB controller. I made a tree, so I had three levels of branches with three and four branches each, and each branch was between two and four feet of LED tape-lights. I think my max was 45 feet of tape. Just figure the amps or watts you will draw based on the number of feet you have! In essence, run all of your light strip leads in parallel as listed on the very helpful face plate of the amplifier. I chose to solder the four-wire connector wire to the LED tapes and used automotive spade terminals to connect the wires together and hold them under the screws. You can probably get away with using the snap-on connectors, wire nuts where needed, and just twist leads together under the screw terminals of the amp if you don't have vibration and moisture I did--prop for marching band show. I had no issues with these amplifiers; solid product! Just remember to keep your RGBW the same for every connection--the tapes care if you reverse them left to right!

So this doesn't need any external power of its own and can just output 24a just from the power one LED strip controller?

Not exactly. If you look at the output section, you will see two power supply connectors for the required power supply. The size of this power supply should be sufficient to cover whatever RGB load you connect to the output connectors.

how many can you connect for each remote control?dc12-24v 288-576w rgb high speed power amplifier 3 channels 24a output current common anode for led s

One is input source the main one you should using to control all the output could be 16 ft. Anything more than that you should be adding another amplifier to boost the signal

Desertcart Logo

Deliver to Madagascar

For best experience Get the App

DOWNLOAD THE APP

WE SOURCE ITEMS FROM

UAE
UK
India
USA
Japan
KOREA

Customer Services

About Us

Customer Support

Description

⚡ Amplify your LED game—because your colors deserve the spotlight!

MASSIVE LOAD CAPACITY - Supports up to 8A per channel, handling intense LED demands effortlessly
PLUG PLAY CONFIDENCE - Designed exclusively for DC12-24V input to ensure safe, reliable performance
POWER UP YOUR RGB SETUP - Amplifies red, green, and blue signals for flawless color consistency
DUAL VOLTAGE FLEXIBILITY - Operates seamlessly on both 12V and 24V DC systems for versatile installations
MAXIMIZE BRIGHTNESS RANGE - Delivers up to 288W (12V) or 576W (24V) output power to extend your LED strips

The 3CH Channels High Speed Power Amplifier by LEDENET boosts RGB LED strip signals with a robust 24A total current capacity, supporting up to 8A per channel. Compatible with DC12V and 24V power supplies, it delivers up to 576W output power, ensuring vibrant, consistent lighting for professional-grade LED installations.

Reviews

J**P

Five Stars

Works very well, does not heat-up, delay not noticeable. Well priced and well made.

23.06.2015

F**H

LED power indicator is a nice feature to make sure the AMP is receiving power

Simple to use, works without any problems. LED power indicator is a nice feature to make sure the AMP is receiving power.You need a DC power jack female plug adapter to provide power to the AMP from a power supply.Used it to connect to LED strips from each other, no fade in color down the strips.

24.05.2017

L**R

Great solution for running multiple LED strips.

Excellent device with plenty of overhead. I needed to hook two 24v 32ft strands together, but was not thrilled about the prospect of delay between the strands from running them end to end with this in the middle. I instead installed this device directly after the controller box, and then ran both strands directly from this amplifier. Two months and no problem, and the best part is that both strands are 100% in sync with each other...no delay! Well made, extremely easy installation, and the unit does not get warm (and is well beneath its maximum current rating) with two full-size 24v strands attached. The price is sweet too. ...Just wanted to review this to be sure that folks know that you don't have to install this between strands. You can install it after the controller and run both strands directly from it to avoid delay. I had to do a ton of research before ordering, and wished somebody else had mentioned this in a review.

22.02.2016

M**D

Great value for general use

I used this to connect a second strip of 5050 RGB LEDs, syncronized with my first set. This unit made the job very easy and straightforward. It works reliably with the strips powered with 24 Volts. My only complaint is that the Green channel seems like it is not quite properly calibrated, so certain colors are not replicated accurately on the second LED strip. Of course, the LED strips could be from different production lots that have different illumination biases--I don't know for sure. Regardless, for my purposes this unit allows me to connect enough lighting to fully wash the front of my house with synchronized light color and brightness, all controlled from a single remote.

3.09.2015

C**S

Sturdy RGB amplifier

Worked exactly as advertised. Did not even heat up noticeably. very solid case.

16.10.2015

E**N

Great Product

Works exactly as intended, boosts and repeats signal perfectly. I'm using this to boost from my 4pin 12v RGB header on my motherboard to sink to my 24v LED wall panel, works fantastic.

12.02.2021

I**Z

Very responsive, Absolutely awesome

Absolutely awesome! Very responsive RGB amplifier and can power a good amount of LED’s, I’ll be ordering a 2nd one soon. This was installed in one of my limos go power under glow and wheel RGB light.

30.03.2020

V**R

Great product and value.

I purchased 2 of these for one of my show cars. Excellent product and a great value. I have had these is use now for several months. One time, I did have the color change from the set color - Red, to a Fuchsia for no reason. After it had been shut down for a while it came back on correct. Other RGB strips running on the same controller were not affected, only the ones running on one of these amplifiers. It only happened one time so not overly concerned. I would definitely recommend and would buy again. In fact, I am considering putting one of these in a watertight box and using a diode bridge rectifier and a landscape transformer to control some long runs of RGB LED strips around my decks.

18.10.2017