darkFlash DLC29 All Mesh PC Case ATX Mid Tower Case High Cooling Performance High Compatibility Gaming Case with USB 3.0 Type-C Interface (Black)

The noise level of this case is basically the same as open air so be aware that your fans will not be muffled by any means.Fits an Asus ROG Strix 3090 OC with an inch or two to spare. I mounted 3x 120mm fans on the outside of the front to give it a bit more room and the front panel still clips on with a tiny bit of room to spare.The included GPU bracket was useful, though with how long my GPU is, one half of it kind of sits over an open area.Black screws included were nice but I wish they included a bunch of fan screws!Overall a nice looking case with basically no airflow restrictions. Room for cables on the backside behind the motherboard made cable management easy. My Corsair HX1200i fit with no issues, probably had a little extra room for something an 1/8" or so bigger. LEDs on GPU and mobo are visible through the mesh but I ended up turning them off anyway.Happy with this purchase and would recommend if you want airflow but with a bit extra dust protection.

Concerning darkFlash DLC29 All Mesh PC Case:This is a very light, compact and reasonably priced case. The overall build quality is adequate and is aesthetically pleasing. I like the perforated panels. The left side (main) panel being perforated means that a vertically mounted GPU will easily able to breath through the perforations (though the vertically mounting provisions are a bit meager). It is also possible to see any RGB lights inside the chassis (should that matter) through the perforated side panel without the risk of fragile glass.Unfortunately, the case was just a bit too small for my purposes. Larger radiators like "ARCTIC Liquid Freezer II 360mm" will (barely) fit in the front. Even though there seems to be space at top for a 240mm radiator, one won't quite fit. If the length of the chassis were about another 25-50mm greater then a 240mm radiator would fit in the top.In addition to a little more length, it would also be good for the PSU shroud to have a larger cutout (near front panel) so that the radiators like the Arctic would fit with out moving the fans to front of the case. If you do not need two radiators or you use a pair of 240mm or a single 360mm radiator then this case would be nice.Overall, I liked it but it doesn't work for me. I ended up using a Corsair 5000D (though I separately purchased a right side panel to replace the glass left side panel).

I got this case for maximum cooling performance. Mesh panels on all side for max air flow. I use a front mounted 360mm AIO, and my CPU (Ryzen 7 5800X) max temp under all core full load never gets above 70*C. My GPU (RTX 3080 Ti) while overclocked pulling 460 watts, maxes out around 74*C. Now with fans running full blast, it gets kind of loud, and also emits heat in all directions, so it's important for this case to be in a well ventilated area. The materials are quality, and it was easy to assemble. Overall I was very happy with my purchase, and would recommend to anyone looking for max cooling. It's not much to look at, but that's not what it's made for.

I wanted a very minimalist case for my engineering work station. I'm not a gamer, and I need for my setup to look professional when clients come to visit. I don't want flashy RGB lights and plexiglass, etc. This case fits the bill very well in that department. A large, black, basically 100% metal mesh case, with 2X very small power HDD activity indicator LEDs on the top. The front has no disk drive access, so it is very clean. There's a power button, reset button , headphone/microphone jacks, 2X USB 3.0 and 2X USB 2.0 ports on the top right next to the status LEDs, in a discreet, very convenient location when the tower is at ground level. Much better than front access ports where I have to lean over to determine what they are. The only real place I can dock it, is there is no panel USB C access, probably because it was designed before USB C was ubiquitous.Once the machine is built, this case gets a 90+/100.Building the machine in this case however, is where the docking of points racks up. This is a pretty cheaply manufactured case and it shows wherever margins could be cut.-The case metal feels relatively flimsy, and the removable panels flex far more than I would imagine them to.-The paint seems very fragile and will likely scratch if it is moved around a lot. Not as much of a problem for me, but may be for others.-The thumbscrews that came with it are plastic and feel cheap. I ended up swapping over my all metal more quality thumbscrews from my old coolermaster case.-The mounting locations for HDDs and SSDs is confusing and poorly laid out to say the least. There's some sort of removable tray that I still have laying around after months, I'm not sure what it's supposed to do.-The PSU mounts at the bottom, which is fine, except the only place for larger HDDs appears to be shoved away in the same cubby with the PSU in the bottom, which makes them hard to access, very crammed if you don't have a modular PSU and need to hide unused wires, and the HDDs don't have tool-less slides for easy access.-The rear PCI access panels aren't replaceable, they are break-away panels that once broken, will remain out. I had a few screw in panels left over from my old coolermaster case that I just broke them all out, and replaced with replaceable panels. Again, only a problem if you change hardware frequently, but beware.-The instructions for the case are (from what I remember) written in Chinese/poorly translated English, and unclear pictures. Be prepared to rack your brain around how something is supposed to be assembled.Ultimately, once the machine is built the case is exactly what I wanted... a very professional looking case housing a workstation with ultimate cooling capabilities (the entire thing has mesh/vent holes in it). If you can suffer through moving your hardware into the case without thinking too much about the poor material quality, and/or salvage some higher quality materials from a higher quality manufacturer, you will end up with a very nice case.I imagine if you are into lights, it would also be a very nice case, because again, the entire thing is a giant mesh structure and would certainly glow through everywhere.

Wasted my time and money

The media could not be loaded. Fanatic case. No glass. All cooling. Enough said.

I like the all mesh design. It will fit an E-ATX motherboard. The metal is kinda thin, but that keeps the weight down. I have 5 fans mounted and no rattles. My ASUS AMD 6950 XT video card barely fit, took some wriggling to get it into place. My 180mm power supply fit nicely, just had to remove the fan cage for it to sit level upside down on the floor of the case. The RGB from my ASUS Crosshair VIII Extreme looks really nice coming through the mesh. Airflow seems really good, the only dust screen is on the top held in place with magnetic strips and it's removable. Case has a power and hard drive activity LEDs. Ultimately, I think it's worth the price.