uxcell M8x40mm Handle Adjustable Clamping Lever Thread Push Button Ratchet Male Threaded Stud Knobs Locking Rotating Screw Handles Quick Release Bolt Black 2pcs

The M8x40 is essentially a drop-in replacement for the obsolete, discontinued, and impossible to get "Lock Lever", Part Number 1340166 for the Delta JT360 6" Jointer. The original handles disintegrated and crumbled years ago and I've been using vice grips ever since... until finally I came across this product. and it works perfectly and is very reasonably priced. Plus now I have a backup because it came in a pack of 2.I got the M10x40 to replace the similarly obsolete, discontinued, and no-longer-available "Lock Lever" Part 1340153, but to get this to work, I also had to pick up a 1/2x5/8x1 steel spacer from the home center and carefully cut it down to 1/2-inch in length so it can effectively replace the original part.

uxcell M8x40mm:This part is high quality and all metal construction. The handle had a very robust powder coating over cast aluminum. I would recommend this brand, hands down! the 40mm was not the correct replacement part for the DELTA 37-190 6" Deluxe Jointer LOCK LEVER, Ref #118, part number 1340166, however, the uxcell M8x60mm WAS a correct replacement.uxcell M8x60mm:The longer uxcell M8x60mm, required a spacer (I used an old junk socket) to replace the LOCK LEVER on the 37-190. The original DELTA part has a spacer integral to the lock lever. I have attached a picture of the uxcell M8x60mm installed with the spacer, and the original delta part beside it. Highly recommend this part for your DELTA and other machine replacement needs.

The picture with the measurements is a little misleading/hard to interrupt. I bought the `M6 x 32mm` size and the image shows the handle length measured where it attaches to the body, not the center of the bolt. The body is 15mm diameter (a dimension not given), the handle 45mm. This means the handle sticks out closer to 50mm from center, which in my case is 2mm too long to spin easily where I'm using it. Otherwise, it works great.

Delta's replacement handles are overpriced. These handles worked perfectly to replace the hold down clamp seen in the photo on my ~20 year old Delta mortiser, but they can also replace the adjustable fence handles, though mine have not yet failed.The handles are solid enough and work perfectly. Would buy again.

Very durable

Little people really keno that can be used on a adventure motorcycle

The M8x40mm size fits the Peloton seat slide adjuster (the one that slides it front to back, not the one that raises it up and down. Not sure what size that one is)40mm is a little longer than the stock part, but the tiny bit extra it sticks out is fine.Peloton wanted to charge me $26 for this same piece — for just a single one! I paid $16 for two, so I feel like I got a deal.I had to use a screwdriver and hammer to chisel the plastic casing off the old Peloton part. Big pain. This new part seems like the handle is more robust, plus if the handle rotation fails, I can always adjust it with a hex key.See my pic — new part is on the left. Notice it’s slightly longer than the old (destroyed by chisel) Peloton part on the right.

My Wali clamp on laptop stand came with a hex bolt requiring a hex wrench to adjust the stand. Not a big deal, but then again not ideal. I lieu of the hex nut I tried a threaded star knob which worked but the small diameter of the knob made it difficult to tighten securely bare handed. The uxcell M8 x 25mm Adjustable Threaded Lever with Push Button Ratchet turned out to be the perfect solution. It is all metal and has a tread pitch of 1.25mm. Just push in the button to engage, then turn away.